Iron Loss Calculation of AC Filter Inductor for Three‐Phase PWM Inverters

In recent years, remarkable advancement of new power semiconductor devices, such as SiC and GaN, enables the increase of switching frequency of power converters, and hence the volume of passive components, such as ac filters and transformers, can be reduced. However, temperature rise caused by the inductor loss is increasing, and hence iron loss evaluation of the inductor is one of the most important issues to realize high power density converters. Conventionally, an improved generalized Steinmetz equation (iGSE) has proposed in order to calculate the iron loss under a pulse voltage magnetizing condition. However, accurate iron loss calculation of the ac filter inductor used in a PWM inverter cannot be realized. The authors have proposed two methods of iron loss evaluation of ac filter inductors. The first one is a loss map method which can calculate the iron loss without using a real PWM inverter. Another one is an ILA (Inductor Loss Analyzer) which can measure the iron loss in every switching period in a real PWM inverter. In this paper, comparisons of the iron loss between the ILA and the loss map method on both the single‐phase and three‐phase inverters are studied. It is found that iron loss of the ac filter inductor in the three‐phase PWM inverter which is calculated by the loss map method cause a large error on a specific condition. In order to prevent the calculation error, the authors proposed a revised loss map method and proved the effectiveness of the method.     

二乙基三胺五乙酸浸取-电感耦合等离子体质谱法测定石灰性土壤中有效态铜锌铁锰

采用二乙基三胺五乙酸(DTPA)浸提石灰性土壤样品中有效态Cu、Zn、Fe、Mn后,样品溶液基体盐分较大,此时若直接采用电感耦合等离子体质谱法(ICP-MS)进行测定,极易使仪器的采样锥和截取锥发生堵塞,雾室和炬管积盐,进而影响测定准确性。据此,实验用DTPA浸提样品后,采用对样品溶液稀释10~30倍和在标准溶液系列中加入DTPA溶液进行基体匹配的方法以消除基体干扰,利用氦碰撞模式进行测定以消除多原子离子⁴⁰Ar¹⁶O对⁵⁶Fe的质谱干扰,最终实现了ICP-MS对石灰性土壤中有效态Cu、Zn、Fe、Mn的测定。对氦气流量进行了优化,并确定氦气流量为4.5mL/min。在优化的实验条件下,Cu、Zn的质量浓度为5~200ng/mL、Fe的质量浓度为100~3000ng/mL、Mn的质量浓度为30~1000ng/mL时,各元素质量浓度分别与其计数值呈线性关系,相关系数均不小于0.9998。方法检出限为0.003~0.01mg/kg。按照实验方法测定土壤有效态成分分析标准物质中的有效态Cu、Zn、Fe、Mn,测定值与认定值一致,相对标准偏差(RSD)为1.3%~3.1%。采用实验方法和标准方法HJ 804—2016(电感耦合等离子体原子发射光谱法)进行方法对照试验,二者测定值基本一致。     

多元合金化大断面球墨铸铁组织和性能的分析

为了提升大断面球墨铸铁综合力学性能，通过复合添加微量合金元素铜、锑、锡、钼对大断面球墨铸铁进行微合金化处理，借助金相显微镜(OM)、扫描电子显微镜(SEM)及力学性能测试等手段，研究了Cu Sb Sn Mo复合微合金化大断面球墨铸铁微观组织和力学性能。结果表明，试验球墨铸铁具有良好的综合力学性能。大断面球墨铸铁中添加铜、锑、锡、钼后优化了材料的组织结构，基体组织为珠光体＋少量牛眼状铁素体；试样石墨组织细小、圆整，分布均匀。同时，合金元素的复合加入使得其抗拉强度达到800 MPa以上，硬度约为280HB，伸长率达到5%以上。拉伸断口分析表明，微合金化大断面球墨铸铁断裂模式以解理断裂为主，伴有少量的塑性变形。     

Preparation of biphasic hydroxyapatite/ β-tricalcium phosphate foam using the replication technique

Biphasic hydroxyapatite/β-tricalcium phosphate foams were prepared using the replication technique starting from a precipitated hydroxyapatite (Ca₁₀(PO₄)₆(OH)₂: HAP) powder, and sodium glycerophosphate (GP). The effect of the grinding time, solid loading, dispersant amount, and etching, replication, and sintering processes were investigated. The SEM, OEM and FTIR analyses proved that the surface of the polyurethane template must be treated with NaOH solution to make it more hydrophilic prior to the coating process. With a solid loading of 40 wt-%, the slurries prepared from the precipitated hydroxyapatite presented a shear thinning behavior, which was useful for the coating process. The SEM analysis of the foams showed that the optimum number of coating layers to obtain foam with an identical structure with the template was limited to three. The use of GP and the optimized preparation parameters helped to decrease the consolidation temperature of the ceramic foams to 1000 °C. The XRD and FTIR analyses of the prepared foams showed that the thermal treatment of the GP and the HAP mixture led to a partial decomposition of the HAP to tricalcium phosphate. The fitting of the XRD patterns and the obtained lattice parameters proved that the decomposition was accompanied by the insertion of sodium from GP toward the lattice of tricalcium phosphate and the formation of Na-β-tricalcium. The results of the SEM analysis, the pore size distribution and the mechanical strength showed that the presence of the Na-β-tricalcium reduced the pore size distribution from 500-2700 to 100–1700 μm, decreased slightly the total porosity from 80 vol-% to 70 vol-%; and improved the mechanical strength of the obtained foam from 1.56 MPa to 2.60 MPa.     

分子筛协同有机磷酸盐改性聚丙烯性能的研究

采用直接混合法制得等规聚丙烯(iPP)/分子筛体系和iPP/有机磷酸盐成核剂(NA11)/分子筛体系,研究不同种类分子筛在不同含量下对iPP结晶温度及力学性能的影响,进而研究不同分子筛在低含量下协同有机磷酸盐对iPP体系成核性能的影响,从动力学角度解释了提升原因。结果表明,单独添加分子筛制得的iPP体系,随着分子筛含量的增加,结晶性能和力学性能得到显著提升,不同分子筛对iPP性能的影响不同,ZSM-5型分子筛在含量为5%(质量分数,下同)以上具有促进iPPβ晶型生成的效果;采用直接混合法制得的不同分子筛复配有机磷酸酯钠盐NA11成核剂可提升iPP的力学性能;特别是当0.1%NA11和0.1%4A型分子筛一起添加到iPP中时,可在保证iPP具有较好刚性的同时兼具有良好的韧性,使iPP的弯曲模量提高35.2%、冲击强度提高14.4%,从而达到促进iPP材料刚韧平衡的效果。     

Phase evolution and microstructure of new Sr0.5Zr2(PO4)3-NdPO4 composite ceramics prepared by one-step microwave sintering

Sodium Zirconium Phosphate (NaZr₂(PO₄)₃, hereinafter NZP) and monazite are both potential materials for immobilization of nuclear waste. In this work, novel (1-x)Sr_0.5Zr₂(PO₄)₃-xNdPO₄ composite ceramics (x = 0, 0.2, 0.4, 0.6, 0.8, and 1.0) for simultaneously immobilizing the simulated fission product (FP) Sr and trivalent minor actinide (MA) Nd were prepared by one-step microwave sintering technique, in which Sr and Nd were immobilized into NZP and monazite type structures, respectively. The phase evolution and microstructure of the samples were investigated by X-ray diffraction (XRD), Raman, and backscattering scanning electron microscopy (BSE). The results showed that the expected composite ceramics were successfully obtained by one-step microwave sintering at 1050 °C for 2 h. The as-prepared samples consisted of Sr_0.5Zr₂(PO₄)₃ and NdPO₄ phases, and the content of the two phases varied regularly as x changed, generally conforming to the designed nominal chemical composition. Importantly, the composite ceramics presented the homogenous and dense microstructure. The relative density of the composite ceramics was more than 95%, meanwhile, the Vickers-hardness of the samples was higher than 600 MPa. It was indicated that NZP-monazite type composite ceramics could be a potential matrix for the simultaneous immobilization of actinide and fission product.     

磷酸脲母液制备工业级磷酸二氢铵工艺研究

湿法磷酸制备磷酸脲过程中会副产大量磷酸脲母液,母液含有金属杂质及五氧化二磷含量较高。采用溶剂萃取法回收磷酸脲母液中五氧化二磷制备工业级磷酸二氢铵（MAP）,分别考察了包括萃取、洗涤、中和、精制、结晶等工艺流程对产品收率及纯度的影响,确定了最佳工艺条件：萃取相比（有机相与水相体积比）=3:1,萃取时间为5 min,萃取温度为50 ℃,洗涤相比（有机相与洗涤剂体积比）=10:1,中和pH为4.5,复合酸性萃取剂PO8皂化率为20%,精制相比（萃取剂与水相体积比）=1:1,浓缩比为1.36,结晶温度为30 ℃。在该条件下制备的工业级MAP纯度可达99.45%,母液中五氧化二磷回收率为85.34%。该工艺对环境友好,原料中五氧化二磷回收率高,具有较高的经济效益。     

磷酸高效分解磷矿实验研究

为改进湿法磷酸生产工艺,提高副产石膏的品质,减少湿法磷酸固体副产物磷石膏堆存产生的经济和环保压力,进行了磷酸分解磷矿制磷酸的实验研究。采用贵州某磷矿为主要原料,研究了湿法磷酸预分解磷矿的反应条件。通过单因素实验确定了湿法磷酸分解磷矿最优反应条件：反应温度为75 ℃,磷酸与磷矿的质量比（液固比）为9,反应时间为3 h,磷酸质量分数为30%（以五氧化二磷计）。在此条件下,磷矿的分解率为98.62%。     

水热法一步合成磷酸铁锂及其性能研究

为优化液相法一步制备磷酸铁锂（LiFePO₄）技术,以七水合硫酸亚铁、磷酸二氢铵、一水合氢氧化锂为原料,通过添加十二烷基苯磺酸钠（SDBS）作为表面活性剂,采用液相水热法合成技术,一步合成了LiFePO₄正极材料。研究了水热法一步合成技术对LiFePO₄材料的组成、结构、形貌、粒度等的影响,通过电感耦合等离子体发射光谱仪（ICP-OES）、X射线衍射仪（XRD）、扫描电镜（SEM）、粒度分析仪等对材料进行了表征分析,并测试了材料的电化学性能。研究结果表明,合成得到的LiFePO₄材料为微米级球形颗粒形貌的正交晶系非化学计量比的Li_1.02Fe_0.994PO₄材料。电化学性能测试结果表明,在0.1C倍率下首次充、放电比容量分别为162.0、159.9 mA·h/g,库伦效率达到98.7%、倍率性能（以1C/0.1C保持率计）为92.3%,0.1C倍率循环100次容量保持率为96.4%,展现出良好的电化学性能。     

集成式铁基质生物膜反应器自养反硝化深度脱氮

以污水厂处理水为研究对象，采用铁基质生物载体与生物膜耦合实现高效自养反硝化脱氮。考察停留时间（HRT）对系统脱氮效能的影响，通过动力学及微生物群落结构分析，揭示耦合技术的脱氮机理。结果表明：HRT为8 h，对一级A和一级B污水厂处理水，总氮(TN)平均去除率分别为95.41%和92.55%，TN处理负荷分别为0.48 kg TN/(m³·d）和0.58 kg TN/(m³·d），硝化过程氨氮(NH₄⁺-N)饱和常数分别为1.17 mg/L和0.72 mg/L，反硝化过程硝氮(NO₃^--N)饱和常数分别为0.87 mg/L和0.67 mg/L。出水水质分别达到《地表水环境质量标准》Ⅲ类、Ⅴ类水质标准。铁基质生物载体与生物膜耦合系统中微生物优势菌属为Maritimimonas、Rhodobacter和Sphaerotilus, 均为自养反硝化菌，证实了铁基质生物载体可为自养反硝化菌提供电子，实现生物自养反硝化脱氮。